- Description
Description
BATTERY SEPARATING FILM PLANT
EXTRUDER
01 SET, PLABOL, JAPAN, 2015
CAPACITY 110 KG/HR, SPEED 40~100MTR/MIN.,
DIE WIDTH 1,600MM,
MAT’L-POLYPROPYLENE, FILM THICKNESS 12~28㎛
EXTRUDER SECTION
SINGLE SCREW Ø90MM,
PRODUCTION 80~110KG/HR,
SCREW SPEED 100RPM,
DRIVING MOTOR 75KW,
THRUST PRESSURE 30~50 MPA
SCREW SECTION
SCREW LENGTH 2,700MM,
DIA Ø89.5~Ø89.8MM, L/D 30, CR 3.0
AIR COOLING SYSTEM, MAT’L-SCM440
CYLINDER SECTION
INNER DIA Ø90MM, OUT Ø180MM, THICKNESS 45MM,
INTERVAL OUT DIA 0.1MM, MAT’L-SACM645
SPEED REDUCER
RATIO 1/18, DIRECT DRIVING SYSTEM
TEMPERATURE CONTROLLER
ALUMINIUM CASTING HEATER,
BAND HEATER, GP AL. CASTING HEATER, CARTRIDGE HEATER,
COOLING ON/OFF
SUPPLY THE RAW MAT’L
HOPPER CAPACITY 120 LTR, AIR SUPPLY SYSTEM
ELECTRIC SECTION
3 PHASE AC380V, HEATER : 1 PHASE 220V
DIES SECTION
WIDTH 1,600MM, TEMPERATURE CONTROL ZONE 12,
CARTRIDGE HEATER
CASTING PARTS & TAKEUP WINDER
FILM WIDTH 1,200MM, FILM THICKNESS 18~28㎛,
LINE SPEED 100 MTR/MIN,
WINDING STRENGTH 5KGF/M, MAX. WINDING DIA Ø1,000MM,
AIR PRESSURE 0.5MPA
FILM STRETCHING MACHINE
01 SET, ICHIKIN CORPORATIO, JAPAN, 2016
BASIC MAT’L : PE, PP
LINE SPEED 3 MTR/MIN,
FILM WIDTH 1,100MM
4 SHAFT FIXED UNWINDER
BOTH SIDE HOLD, CONE CHUCK,
RAIL MOVEMENT SYSTEM
FILM WINDING DIA Ø1,250MM, W’T 1,300 KG,
WIDTH 1,450MM, 8″ INNER DIA
FEED ROLL UNIT
INLET ROLL DIMENSION Ø250 x 1,300MM,
VECTOR INVERTER ROLL DRIVING,
GUIDE ROLL Ø150 x 1,300MM
STRETCHING SECTION
HEAT DRIVE ROLL TEMPERATURE CONTROL-INDUCTION HEATING,
EFFECTIVE WIDTH 1,200MM,
VECTOR INVERTER MOTOR, OVEN-DOWN FLOW SYSTEM,
INSULATION BOARD-GLASS WOOL,
GUIDE ROLL Ø150 x 1,300MM
CARRIER CHAIN
SETTING RANGE-STRETCHING UNIT
WINDER
SHAFT HOLDING-SINGLE SHAFT FIXED SYSTEM,
WINDING DIA Ø1,400MM, MAX. WIDTH 1,100MM,
W’T 1,050KG, 8″ CORE DIAMETER,
VECTOR INVERTER DRIVING
MAIN DRIVING MOTOR
INDUCTION MOTOR & CONTROL PANEL
POWER SOURCE POWER CIRCUIT-3 PHASE AC 380V
CONTROL CIRCUIT-SINGLE PHASE AC 220V, DC 24V
CONTROL PANEL
NON-EXPLOSION PROOF INDOOR, CONTENT DRVIE CONTROL PANEL
NON-EXPLOSION PROOF INDOOR, INSTALLATION POINT MAIN MACHINE,
WINDER
UTILITY
POWER CLASSIFICATION 380V, 220V 3 PHASE
AIR COMPRESSOR : OIL FREE SYSTEM,
PRESSURE 0.5 MPA, DRY AIR
WATER CLASSIFICATION : PRESSURE 0.2MPAG
LAMINATING MACHINE
01 SET, P&T, KOREA, 2015
MAT’L PP FILM,
FILM WIDTH 1,200MM,
FILM THICKNESS 16-20μm,
ROLL WIDTH 1,400MM,
SPEED 50`70 MTR/MIN,
TAKE-UP DIA Ø950~Ø1,250MM,
UNWIND & REWIND TENSION 70N~200N,
CORE (UNWIND, REWIND)
INNER DIA Ø8″ AL.CORE
AIR COMPRESSOR 4.5~7 KG/S.MTR,
REWINDING DEVIATION-MAX. 3MM
FILM SEPARATING MACHINE
01 SET, P&T, KOREA, 2015
MAT’L PP FILM,
FILM WIDTH 1,100MM,
FILM THICKNESS 16-20μm, 4~16 LAYERS,
ROLL WIDTH 1,400MM,
SPEED 50~100 MTR/MIN,
WINDING DIA Ø700~Ø1,350MM,
UNWIND TENSION 70N~200N,
REWIND TENSION 20N~50N,
UNWINDING CORE ID Ø6″ ABS, Ø8″ AL. CORE
REWINDING CORE ID Ø6″ ABS CORE,
TAKE-UP : UP/DOWN,
FILM SLITTING MACHINE
01 SET, P&T, KOREA, 2015
PRODUCTION SPEED 60~120 MTR/MIN,
MAT’L SEPARATE FILM,
FILM THICKNESS 20㎛~16㎛,
FILM WIDTH 400~1,200MM,
SLITTING WIDTH 150~830MM,
ROLL WIDTH 1,300MM,
MACHINE SPEED 120 MTR/MIN,
WINDING DIA Ø400MM,
UNWINDER COE INNER DIA Ø3″, Ø6″,
TAKE-UP UP/DOWN
AIR COMPRESSOR
NORMAL 5~7KG/S.CM
